Call Us Now! +86-15705695515

Order Online Now! sunnytao@ahjnge.net.cn

wind solar hybrid controller
News
New Products
  • wind solar hybrid charge controller
    The Latest Privilege Version MPPT Wind Solar Hybrid Charge Controller With Wifi/ GPRS Monitor

    > Remote Monitoring by 3 ways: PC monitoring; WIFI by mobile phone; GPRS by mobile phone. >This new wind solar hybrid controller is special design for 0-800w wind and 0-600w solar panels for wind >solar street light or home wind solar complementary system. >Appearance is elegant, operations are easy. Uses a custom digital LCD screen can see solar panel ,wind turbine, battery status and four key operation mode. The user to use simple and easy to use, popular and  >The inner circuit board of the controller is sprayed to prevent dust, moisture and static electricity, which can effectively prolong the controller' service life. >This controller can workable to Gel, Lead-acid, Ternary lithium battery and Lithium iron phosphate battery. >Lightning counter-attack, solar charger, over-voltage automatic braking, storage battery reverse connect and open protection, etc.

  • MPPT solar charge controller
    Mini MPPT Solar Charge Controller 10amp 20amp 30amp for solar power system

    Latest JN-MPPT-Mini MPPT solar charge controller ranges from 10amp 20amp 30amp with mini smart design for various use purpose . The battery system voltage is 12v 24v 48v auto recognize and max. PV input can be 150V. High charge efficiency is above 99.8% which is much cost-effective for project.

  • MPPT solar charge controller
    Latest MPPT Solar Charge Controller 30amp 40amp 50amp for solar power system

    Latest JN-MPPT-AL MPPT solar charge controller ranges from 30amp 40amp 50amp which are used for solar panel system . The battery system voltage is 12v 24v 48v auto recognize and max. PV input can be 150V. High charge efficiency is above 99.8% which is much cost-effective for project.

  • PWM Solar Charge Controller
    Lastest Design PWM Solar Charge Controller 100A 24V 48V 96V 110V 192V 220V 240V

    Latest JND-X series PWM solar charge controller is used in solar off-grid system (independent system), especially suitable for small off-grid solar power generation control system, which automatically adjusts charging and discharging. The battery charging process of the JND-X controller is optimized to extend battery life and improve system performance.

Notes for Inverter's Installation

2017-11-02

1. Before installation, you should check whether the inverter is damaged or not during transportation.

2. When selecting the installation site, you should ensure that there is no interference from any other power electronic equipment in the surrounding area.

3. Before you making electrical connections, please use opaque material covered the PV panel or disconnected the DC-side circuit breaker. Photovoltaic arrays will produce dangerous voltages if them are exposure to sunlight.

4. All installation operations must be done only by professional technicians.

5. The cables used in the PV system must be securely connected, well insulated, and properly sized.

6. All electrical installations must meet local and national electrical standards.

7. The inverter ca be connected after the local power sector has been approved and all electrical connections have been made by a professional technician.

8. Before performing any maintenance work, first you need disconnect the connection between inverter and electrical grid, then disconnect the DC side electrical connection.

9. Wait at least 5 minutes until the internal components are discharged, then you can repair the inverter.

10. Before turning on the inverter again, any machine failure that can affects the inverter safety must be immediately removed .

11. Avoid unnecessary board contact.

12. Observe the static protection standard, wear anti-static bracelet.

13. Watch and follow the warning signs on the product.

14. Perform a preliminary visual inspection of the equipment for damage or other dangerous conditions.

15. Attention the inverter hot surface, such as power semiconductor heat sink. Because the inverter still maintain a high temperature after it is power off.

Position Requirements of Inverter Installation

1. Do not install the inverter in direct sunlight position. Otherwise it may cause additional internal temperature, even the temperature is too high lead to inverter temperature failure.

2. Select a installation site should be strong enough to support the weight of the inverter for a long time.

3. The installation site should at an ambient temperature between -25 ° C to 50 ° C, the installation environment should be clean.

4. The environment humidity of installation site should be below 95%, and no condensation.

5. There should be enough clearance in front of the inverter to make it easy to observe data and repair.

6. Install the inverter as far as away from the residents, because its operation will produce some noise.

7. Installation place should be stable, can not be shake.

Newsletter

Sign up receive company information

Contact Us

PHONE/WHATSAPP :

+86-15705695515

Skype :

jngesunny

Address :

No. 99,Yonghe Road, high-tech Zone, Hefei city ,Anhui Province, China

Copyright © 2015-2020 Anhui JNGE POWER Co.,LTD.All Rights Reserved.Powered by dyyseo.com

Tel : +86-15705695515

Wechat : +86-15705695515

whatsapp : +86-15705695515

skype : jngesunny

Email : sunnytao@ahjnge.net.cn

contacts Home
收缩 展开
  • Subject
  • Tel
  • Email*
  • Message*
  • Please double check your mailbox for fear of any mistake.